Rodless cylinders Series 52
Double-acting, magnetic, cushioned
Ø 25, 32, 40, 50, 63 mm
Ø 25, 32, 40, 50, 63 mm
Series 52 rodless cylinders are available in 5 diameters (25, 32, 40, 50 and 63 mm) and comes in three main versions: Basic (M), with Slide bearing (G) and with Roller bearings (R).
Furthermore these three main versions are each available with either standard- or short carriage to cover a wider range of applications.
Furthermore these three main versions are each available with either standard- or short carriage to cover a wider range of applications.
A permanent magnet is assembled on the piston allowing the position to be detected by means of proximity switches positioned in grooves located on 3 sides on the cylinder profile.
The cylinder is equipped with an end stroke cushioning which can be regulated by means of a screw located on each end cover of the cylinder.
These cylinders are also available in versions with air supply from one side (end cover) only if needed.
General Data
| Models | Standard, with slide bearings, with roller bearings, air supply from one or both sides, with standard or short carriage. For sizes 50 – 63 roller bearings version is not available. |
| Materials | AL (anodized), plastic, hardened steel, seals: NBR, PU |
| Operating temperature | -10°C ÷ +70°C |
| Operating pressure | 1 ÷ 8 bar 1,5 ÷ 8 bar (Ø25 for “R” version) |
| Speed | 10 ÷ 1000 mm/sec (without load) |
| Fluid | Filtered air, without lubrication. If lubricated air is used, it is recommended to use ISO VG 32 oil. once applied the lubrication should never be interrupted. If speeds exceed 1 m/s lubricated air is recommended. |
| Bore size | Ø25 Ø32 Ø40 Ø50 Ø63 |
| Cushioning length (mm) | 14 mm – Ø25 20 mm – Ø32 25 mm – Ø40 22 mm – Ø50 32 mm – Ø63 |
| Strokes with standard carriage (version “P”) | Max. 6000 mm – Ø25 Max. 5950 mm – Ø32 Max. 5900 mm – Ø40, 50 Max. 5880 mm – Ø63 |
| Strokes with short carriage (version “C”) | Max. 6000 mm |
| Stroke tolerance | Strokes ≤ 1000 mm = 0 / +0,6 mm Strokes > 1000 mm = 0 / +3 mm |
| Connection | G1/8 (Ø25, 32) G1/4 (Ø 40) G3/8 (Ø 50, 63) |
Coding Example
| 52 | M | 2 | P | 40 | A | 0500 |
| 52 | SERIES | |
| M | VERSION M = standard G = with slide bearing R = with roller bearing (only Ø 25 – 32 – 40) | |
| 2 | OPERATION 2 = double-acting, cushioned, with air supply from both sides 8 = double-acting, cushioned, with air supply from one side only | PNEUMATIC SYMBOLS CDSS (see the following pages) CDSS (see the following pages) |
| P | MATERIALS P = anodized AL profile tube, NBR and PU seals, standard carriage C = anodized AL profile, NBR and PU seals, short carriage | |
| 40 | BORE 25 = 25 mm 32 = 32 mm 40 = 40 mm 50 = 50 mm 63 = 63 mm | |
| A | TYPE OF MOUNTING A = standard | |
| 0500 | STROKE (see table) |
