Cylinders Series 40K
Double acting, cushioned, magnetic
Ø 160 – 200 – 250 – 320 mm
Ø 160 – 200 – 250 – 320 mm
Series 40K cylinders comply with the ISO 15552 standard and can be assembled with the entire range of standard accessories.
A permanent magnet on the piston of these cylinders is able to send, through proximity switches mounted on the cylinder sliding axis, electrical signals to indicate its position.This series is normally equipped with end-stroke cushioning which can be adjusted through a screw on the end block.
A permanent magnet on the piston of these cylinders is able to send, through proximity switches mounted on the cylinder sliding axis, electrical signals to indicate its position.This series is normally equipped with end-stroke cushioning which can be adjusted through a screw on the end block.
General Data
| Operation | Double-acting |
| Design | ISO 15552 |
| Materials | Coated AL end blocks AL piston Rolled AISI 420B stainless steel (Ø 160, 200 mm) or chrome plated steel (Ø 250, 320 mm) rod Zinc-plated steel rod nut Anodized AL tube Zinc-plated steel tie-rods and tie-rod nuts NBR-PU rod – piston and cushion seals Brass rod scraper ring |
| Mounting | Front flange, rear flange, foot mounts, centre trunnion, front and rear trunnion |
| Strokes min – max | 10 ÷ 2500 mm |
| Working temperature | 0°C ÷ 80°C (with dry air – 20°C) |
| Working pressure | 1 ÷ 10 bar |
| Speed | 10 ÷ 500 mm/sec (without load) |
| Fluid | Filtered air, without lubrication. If lubricated air is used, it is recommended to use oil ISOVG32. Once applied the lubrication should never be interrupted. |
Coding Example
| 40 | K | 2 | L | 160 | A | 0200 |
| 40 | SERIES | |
| K | VERSION K = Standard, magnetic | |
| 2 | OPERATION 2 = Double-acting, front and rear cushions 3 = Double-acting, no cushion 4 = Double-acting, rear cushions 5 = Double-acting, front cushion 6 = Double-acting, through-rod, front and rear cushions 8 = Double-acting, through-rod, no cushion | PNEUMATIC SYMBOLS CD09 CD07 CD37 CD38 CD13 CD14 |
| L | MATERIALS L = See the General Data table on the previous page T = AISI 420B stainless steel tie-rods – AISI 303 stainless steel tie-rod nuts C = Rolled AISI 303 stainless steel piston rod, AISI 304 stainless steel piston rod nut U = AISI 303 rolled stainless steel piston rod, AISI 304 stainless steel piston-rod nut AISI 420B stainless steel tie-rods, AISI 303 stainless steel tie-rod nuts W = AISI 304 rolled stainless steel piston rod, AISI 304 stainless steel piston-rod nut AISI 420B stainless steel tie-rods, AISI 303 stainless steel tie-rod nuts.The rod of cylinders with bore of 250 and 320 mm is in C45E chrome plated steel. | |
| 160 | BORE 160 = 160 mm 200 = 200 mm 250 = 250 mm 320 = 320 mm | |
| A | TYPE OF BRACKET A = Standard F = Cylinder with centre trunnion | |
| 0200 | STROKE | |
| = Standard V = FKM rod seals W = All FKM seals +130°C C = PU coated. Colour: Grey [available on request] G = With brass rod scraper (chrome plated AISI 420B stainless steel rod, NBR rod seal) [Ø 250 and 320 excluded] ( _ _ _ ) = Extended piston rod _ _ _ mm | ||
| CERTIFICATIONS EX = ATEX |
